汽车内饰用液压压力机
汽车内饰专用液压压力机性能特点：
1、有四柱和框架二种结构，机身采用有限元件结构分析和优化设计，结构合理。
2、采用多缸结构，确保大台面承压均匀。
3、液压系统采用集成式插装阀控制，动作灵敏、可靠，无渗漏。
4、PLC控制的电气系统，性能可靠，柔性好。
5、汽车内饰专用压力机设有液压回路和滑块上限位锁紧机构，安全性能好。
注：可根据用户要求特殊定做！
Performance and Characteristic:
1、The forming press has two kinds of structure:four-column and framed type. Its body adopts computer finite element structure analysis and optimized design, with a reasonable structure.
2、The forming press adopts multi-cylinder structureto assure a balance bearing force in large-sized table.
3、The hydraulic system adopts integrated cartridge valve, with sensitive and reliable actions and no leaking.
4、The electrical system adoptsd PLC control, with reliable performance and brtter feasibility.
There set a hydraulic safety circuit and slide locking device in up dead point, with the better safe performance.
5、With the built-in frequency conversion technology, electricity could be save more than 30%.
| 项目 | 单位 | 200T | 300T | 400T | 500T | |
| 公称力 | KN | 2000 | 3000 | 4000 | 5000 | |
| 工作液体压力 | Mpa | 21 | 23 | 23 | 23 | |
| 回程力 | KN | 630 | 630 | 630 | 1000 | |
| 滑块行程 | mm | 1200 | 1200 | 1200 | 1200 | |
| 开口高度 | mm | 1400 | 1400 | 1400 | 1400 | |
| 工作台尺寸 | 左右 | mm | 3000 | 3000 | 3000 | 3000 |
| 前后 | mm | 2500 | 2500 | 2700 | 2700 | |
| 滑块快降速度 | nm/s | 100-300 | 100-300 | 100-300 | 100-300 | |
| 滑块慢压速度 | nm/s(可调) | 41501 | 41501 | 41501 | 41501 | |
| 滑块微压速度 | nm/s(可调) | 41279 | 41279 | 41279 | 41279 | |
| 滑块快回速度 | nm/s | 150 | 150 | 150 | 150 | |
| 最大模具重量 | T | 10T | 15T | 15T | 15T | |
| 工作台至地面高度 | mm | 730 | 730 | 730 | 730 | |
| 总高度 | mm | 6200 | 6500 | 6500 | 6900 | |
| 电机功率 | Kw(约) | 45 | 55 | 75 | 90 | |
| 机器重量 | T(约) | 52 | 58 | 65 | 72 | |
| 机器地面以下深度 | mm | 250 | 550 |
上一个产品: 防盗门专用液压压力机/2000吨防盗门压花机 下一个产品: 门板压花液压压力机
